Need help choosing an elevator or planning modernization? Talk to a Kone people-flow advisor today.

The Division 10 Questions I Got Wrong So You Don't Have To

Eleven years handling Division 10 specialty orders. Twenty-three documented mistakes. Roughly $18,000 in wasted budget that I can still itemize if you want the spreadsheet. Here are the questions I wish someone had answered for me in 2014.

What exactly counts as "construction specialties"?

Short answer: almost anything under CSI MasterFormat Division 10 that isn't structural. Wall protection, expansion joints, louvers, sunshades, grilles, corner guards, kick plates, door products—the stuff architects specify at 2 a.m. and contractors install at the very end of the schedule when everyone's already tired.

Here's what nobody tells you: Division 10 is weirdly fragmented. You can buy wall protection from one vendor, expansion joints from another, and louvers from a third, and none of them talk to each other. In my first year (2014), I submitted a package with corner guards that didn't match the wall protection color. Looked fine on my screen. The architect rejected it in about 20 minutes. That was a $640 mistake—guards got remade, and we ate the freight.

What is C/S Gridline 2 and why does it keep coming up?

C/S Gridline 2 is part of the Construction Specialties wall protection family—specifically their modular grid system for mounting wall guards. Acrovyn is the flagship material (the heavy-duty sheet that takes an impact without cracking), and Gridline 2 is the mounting framework that lets you swap individual panels without tearing out the whole wall.

Why it keeps coming up: architects like it because it looks clean, contractors like it because it's modular. I like it because in September 2022 I finally learned to check the substrate before ordering. We installed 40 linear feet of Gridline 2 on a wall that wasn't plumb—or rather, it was plumb at the top and 3/8" out at the bottom. Panels went up. They didn't stay straight. Cost to fix: $1,200 plus a two-day delay while we shimmed and re-hung.

How do smaller suppliers like AJ Construction Specialties compare?

I'm going to deliberately not rank specific companies here—that's a fast way to get a legal letter and a worse reputation. What I can tell you is the framework we use to evaluate any Division 10 supplier, big or small.

Three questions: (1) Can they send a physical sample within a week? (2) Do they answer technical questions without transferring you to a sales rep who reads from a brochure? (3) What's their lead time when a job goes sideways?

We switched wall protection vendors in 2021 because the first one couldn't hit a six-week lead time. The new one could—but their documentation was sloppy. We spent 14 hours fixing submittal packages that should have taken 3. That's a different kind of expensive.

Do stained glass windows fall under construction specialties?

Technically yes—they're decorative specialties, usually Division 10 40 00 or a custom section. Practically, they're a completely different animal.

Stained glass needs protection during construction. I learned this in 2018 when a crew staged drywall too close to a protected window opening. One dropped board, one cracked panel, $2,800 to restore—or rather, to replace, because the artist who made the original had retired.

If you're specifying stained glass on a job with active construction, budget for plywood enclosures and a conversation with your GC about staging. It's not a Division 10 problem, but it becomes your problem when the glass breaks.

Where do solenoid valves fit into a Division 10 spec?

I'm not a mechanical engineer, so I can't speak to solenoid valve sizing or coil voltage—that's Division 22 (Plumbing) or Division 23 (HVAC) territory. What I can tell you from a specialty-products perspective is that solenoid valves show up in our world when they're part of automated louvers or motorized sunshades. The valve itself is usually specified under the louver section, but the electrical connection is—well, it depends on who you ask.

That ambiguity causes RFIs. In Q1 2024, we had a project where the solenoid for a motorized louver was specified in Division 23 but physically mounted on a Division 10 product. Three weeks of back-and-forth, and the electrician showed up before the louver was installed. Nobody's fault, really—just a spec coordination gap.

The question nobody asks: why can't you just copy and paste specs between projects?

Because specs carry hidden context, and copying is too easy.

I made this mistake in 2017. Copied a hospital Division 10 spec, pasted it into a school project template. Same products, same densities, same everything—I thought. (Side note: I was working on a Chromebook that week, and the copy-paste workflow on ChromeOS is stupidly fast—Ctrl+C, Ctrl+V, done. That speed is exactly the problem. You paste before you think.)

The hospital spec called for antimicrobial wall protection. The school didn't need it. We ordered 52 Acrovyn panels with the wrong finish—$1,976 in material, plus a four-week reorder delay that pushed the school's opening by 11 days.

The fundamentals of impact resistance haven't changed since 2017. But compliance requirements have. What was correct in a 2020 hospital spec may be wrong for a 2025 school. Check every line, every time.